Kingspan Thermawall TW50 PIR - 75mm (6/pack)
Additional Info
Kingspan
C-543
-
Application:
Insulation board for use in partial fill cavity walls -
Type:
Rigid thermoset polyisocyanurate (PIR)
-
Product Size:
1200mm x 450mm -
Thickness:
75mm -
Pack Coverage:
3.24m2 -
Estimated Delivery:
3-5 Working Days
Product Description
Kingspan Thermawall TW50 PIR - 75mm (6/pack)
75mm Kingspan Thermawall TW50 PIR Insulation
High performance partial fill cavity wall insulation Kingspan Thermawall TW50 is a high performance insulation with a fibre-free rigid thermoset polyisocyanurate (PIR) core.
It is used to insulate cavity walls, and has a thermal conductivity of 0.022 W/m·K.
Thickness: 75mm
All thickness : 25mm,30mm,40mm,45mm,50mm,60mm,70mm,75mm,100mm
Length: 1200mm
Width: 450mm
Pack coverage: 3.24m2
Weight/m2: 2.40kg
Thermal conductivity: 0.022 W/mK
Thermal resistance: 3.40m²K/W
Facings: Low emissivity composite foil
Keys facts:
High performance rigid thermoset insulation – thermal conductivity 0.022 W/m.K
Clear cavity is maintained – resists moisture penetration
Low emissivity foil facings significantly increase the thermal resistance of the cavity
Meets NHBC technical requirements when used with a 50 mm residual cavity
Unaffected by air infiltration
Easy to handle and install
Non–deleterious material
Manufactured with a blowing agent that has zero ODP and low GWP
The Facings
Kingspan Thermawall® TW50 is faced on both sides with a low emissivity composite foil, autohesively bonded to the insulation core during manufacture. This reflective, low emissivity surface improves the thermal resistance of any unventilated cavity adjacent to the board.
The Core
The core of Kingspan Thermawall® TW50 is manufactured with Nilflam® technology, a high performance fibre–free rigid thermoset polyisocyanurate (PIR) insulant manufactured with a blowing agent that has zero Ozone Depletion Potential (ODP) and low Global Warming Potential (GWP).
Compressive Strength
The compressive strength of Kingspan Thermawall® TW50 typically exceeds 125 kPa at 10% compression, when tested to BS / I.S. EN 826: 2013 (Thermal insulating products for building applications. Determination of compression behaviour).
Water Vapour Resistance
Adjusted for the effect of board joints, the product typically achieves a resistance far greater than 100 MN.s/g, when tested in accordance with BS / I.S. EN 12086: 2013 (Thermal insulating products for building applications. Determination of water vapour transmission properties).
Durability
If correctly installed, Kingspan Thermawall® TW50 can have an indefinite life. Its durability depends on the supporting structure and the conditions of its use.
Fire Performance
Kingspan Thermawall® TW50, is Class 1, as defined by BS 476–7: 1997 (Fire tests on building materials and
structures. Method of test to determine the classification of the surface spread of flame of products).
Kingspan Thermawall® TW50 will not prejudice the fire resistance properties of a wall in which it is installed. It is
unlikely to become ignited within the cavity. If fire does penetrate into an unventilated cavity, the amount of air present
will be insufficient to support combustion, and flame spread will be minimal.
Insulation Product Benefits
With a declared value thermal conductivity of 0.007 W/m·K, these products provide an insulating performance that is up to five times better than commonly used insulation materials.
Provides high levels of thermal efficiency with minimal thickness.
Over 90% (by weight) recyclable.
Packaging and Storage
The polyethylene packaging of Kingspan Insulation products, which is recyclable, should not be considered adequate for outdoor protection.
Ideally, boards should be stored inside a building.
If, however, outside storage cannot be avoided, then the boards should be stacked clear of the ground and covered with an opaque polythene sheet or weatherproof tarpaulin. Boards that have been allowed to get wet should not be used.
Kingspan Thermawall TW50 PIR - 75mm (6/pack)
When you order from opencartworks.com, you will receive a confirmation email. Once your order is shipped, you will be emailed the tracking information for your order's shipment. You can choose your preferred shipping method on the Order Information page during the checkout process.
The total time it takes to receive your order is shown below:
The total delivery time is calculated from the time your order is placed until the time it is delivered to you. Total delivery time is broken down into processing time and shipping time.
Processing time: The time it takes to prepare your item(s) to ship from our warehouse. This includes preparing your items, performing quality checks, and packing for shipment.
Shipping time: The time for your item(s) to tarvel from our warehouse to your destination.
Shipping from your local warehouse is significantly faster. Some charges may apply.
In addition, the transit time depends on where you're located and where your package comes from. If you want to know more information, please contact the customer service. We will settle your problem as soon as possible. Enjoy shopping!
All delivery charges are included in the final shopping basket and are dependent on the products Scottish Highlands & the Islands where additional shipping charges will apply.
Please note that not all products will incur an additional delivery charge to the Scottish Highlands & the Islands – this is based on the costs from the manufacturer, distributor or courier providing shipping on our behalf. If your delivery address is in the Scottish Highlandsand Islands, a member of our helpline team will contact you prior to processing your ordershould an additional delivery charge apply.
While we make every effort to ensure orders are delivered by the date required, we cannot guarantee availability from the manufacturer or the manufacturer's delivery schedules.
Any variation to web delivery date given will be advised to you by email or telephone. If we are unable to make delivery because access is not possible, we reserve the right to make a failed delivery charge.
