Kingspan Kooltherm K106 Cavity board - 80mm(6/pack)
Kooltherm K106 Cavity Board
Premium performance cavity wall insulation, kingspan Kooltherm K106 Cavity Board is a premium performance insulation with a fibre-free rigid thermoset phenolic core. As part of our Kooltherm K100 range, it provides a level of performance that is unrivalled in the world of rigid thermoset insulation materials with a thermal conductivity of just 0.018 W/m·K across all thicknesses.
Manufactured with a blowing agent that has zero ODP and low GWP, it is used to insulate cavity walls with just a 10 mm residual cavity.
Available thicknesses: 80mm,90mm,100mm,115mm
Pack size: 6 no.
Pack coverage: 3.24m2
Compressive Strength: typically exceeds 100 kPa
Thermal Conductivity: 0.018 W/m.K
Thermal Resistance (R–value): 4.40 m2.K/W
Core: Premium performance lower-lambda rigid thermoset phenolic insulation manufactured with a blowing agent that has zero Ozone Depletion Potential (ODP) and low Global Warming Potential (GWP)
Reverse facing: Water-tight, vapour-open polypropylene fleece
Inner facing: Low emissivity composite foil
Green Guide Rating: Kingspan Kooltherm K106 Cavity Board achieves a Green Guide Rating of A+
Premium performance rigid thermoset phenolic insulation – thermal conductivity of 0.018 W/m.K
10 mm cavity is maintained – resists moisture penetration
The water–tight, vapour–open polypropylene fleece outer facing protects against moisture penetration
Unaffected by air infiltration
Easy to handle and install
Manufactured with a blowing agent that has zero ODP and low GWP
The outer facing of Kingspan Kooltherm® K106 Cavity Board is a water–tight, vapour–open polypropylene fleece. The inner facing is a low emissivity composite foil, autohesively bonded to the insulation core during manufacture.
The core of Kingspan Kooltherm® K106 Cavity Board is a premium performance fibre–free rigid thermoset phenolic insulant manufactured with a blowing agent that has zero Ozone Depletion Potential (ODP) and low Global Warming Potential (GWP).
The compressive strength of Kingspan Kooltherm® K106 Cavity Board typically exceeds 100 kPa when tested to BS / I.S. EN 826: 2013 (Thermal insulating products for building applications. Determination of compression behaviour).
If correctly installed, Kingspan Kooltherm® K106 Cavity Board can have an indefinite life. Its durability depends on the supporting structure and the conditions of its use.
Resistance to Solvents, Fungi & Rodents
The insulation core is resistant to short–term contact with petrol and with most dilute acids, alkalis and mineral oils. However, it is recommended that any spills be cleaned off fully before the boards are installed. Ensure that safe methods of cleaning are used, as recommended by suppliers of the spilt liquid.
Standards & Approvals
Kingspan Kooltherm® K106 Cavity Board is manufactured to the highest standards under a management system certified to ISO 9001: 2008 (Quality Management Systems. Requirements), ISO 14001: 2004 (Environmental Management Systems. Requirements), BS OHSAS 18001: 2007 (Occupational Health and Safety Management Systems. Requirements) and ISO 50001: 2011 (Energy Management Systems.
Kingspan Kooltherm® K106 Cavity Board will not prejudice the fire resistance properties of a wall in which it is installed. It is unlikely to become ignited within the cavity. If fire does penetrate into an unventilated cavity, the amount of air present will be insufficient to support combustion, and flame spread will be minimal.
Kingspan Kooltherm® K106 Cavity Board is normally held in position by the wall ties used to tie the two skins of masonry together.
Wall ties should include a retaining disc / clip of a thickness no greater than 10 mm.
For a solid concrete ground floor the first row of wall ties are installed in the inner leaf at 600 mm horizontal centres a minimum of one course of blockwork below the damp proof course, or 150 mm (for the UK) and 225 mm (for Ireland) below the top surface of the ground floor perimeter insulation upstand, whichever is the lower
For a suspended timber floor the first row of wall ties are installed in the inner leaf at 600 mm horizontal centres a minimum of 200 mm below the top surface of the ground floor perimeter insulation upstand.
Continue constructing the inner leaf up to the next wall tie course (450 mm above the first – usually 2 block courses).
The next course of wall ties is positioned at the usual 900 mm horizontal centres in the UK and 750 mm horizontal centres in Ireland.
The next course of blockwork is installed to secure the ties.
The first row of insulation boards should now be installed between the two rows of wall ties, ensuring each insulation board is retained tight against the inner leaf and joints are lightly butted.
The tape should be applied in a smooth and wrinkle–free manner and should extend no less than 50 mm either side of joints, board edges and abutting junction interfaces. If necessary, additional layers of tape may be applied. The seal must be maintained at protrusion locations e.g. wall ties.
To ensure successful adhesion, all surfaces to receive tape should be made clean, dry and free from grease, dust, dirt and all other foreign matter prior to application. A gentle pressure may also be exerted during application.
The outer leaf is then built up to the level of the top of the boards and the process is repeated.
When insulating a gable, insulation boards should be continued 200 mm beyond the height of the top storey ceiling and a cavity tray installed above the insulation.
For further advice please contact the Kingspan Technical Service:
Tel: ( +44 1544 388601)
Kingspan Kooltherm K106 Cavity board - 80mm(6/pack)
When you order from opencartworks.com, you will receive a confirmation email. Once your order is shipped, you will be emailed the tracking information for your order's shipment. You can choose your preferred shipping method on the Order Information page during the checkout process.
The total time it takes to receive your order is shown below:
The total delivery time is calculated from the time your order is placed until the time it is delivered to you. Total delivery time is broken down into processing time and shipping time.
Processing time: The time it takes to prepare your item(s) to ship from our warehouse. This includes preparing your items, performing quality checks, and packing for shipment.
Shipping time: The time for your item(s) to tarvel from our warehouse to your destination.
Shipping from your local warehouse is significantly faster. Some charges may apply.
In addition, the transit time depends on where you're located and where your package comes from. If you want to know more information, please contact the customer service. We will settle your problem as soon as possible. Enjoy shopping!
All delivery charges are included in the final shopping basket and are dependent on the products Scottish Highlands & the Islands where additional shipping charges will apply.
Please note that not all products will incur an additional delivery charge to the Scottish Highlands & the Islands – this is based on the costs from the manufacturer, distributor or courier providing shipping on our behalf. If your delivery address is in the Scottish Highlandsand Islands, a member of our helpline team will contact you prior to processing your ordershould an additional delivery charge apply.
While we make every effort to ensure orders are delivered by the date required, we cannot guarantee availability from the manufacturer or the manufacturer's delivery schedules.
Any variation to web delivery date given will be advised to you by email or telephone. If we are unable to make delivery because access is not possible, we reserve the right to make a failed delivery charge.