ProWarm Electric Underfloor Heating 150W Sticky Mat ( 14m2 - 2 mats )

ProWarm Electric Underfloor Heating 150w Sticky Mat

ProWarm Electric Underfloor Heating 150w Sticky Mat  is suitable as a primary heating source providing you have adequate insulation. These are our most commonly used heating mats for kitchens, dining rooms, large bathrooms, and most other areas with tiled floors.

Heating Type: Electric Systems
Twin Conductor: 150W
Length: 28m
Width: 0.5m
Area: 14m²
Watts: 100W
Voltage: 230V
Resistance: 352.00 (Ohms)
Floor Construction Suitability: Concrete & Timber
Suitable for: Under Tiles
Material: Fluropolymer coated resistive electrical heating elements
Pack Quantity: 1
Years Guaranteed: 25
Type: Underfloor Heating Mats

100 WATT mats - 100w/m2 underfl oor heating mats provide a highly economical fl oor warming system and are used to cover larger areas.
150 WATT mats - 150w/m2 underfl oor heating mats are suitable as a primary heating source providing you have adequate insulation.

200 WATT mats - 200w/m2 underfl oor heating matsare generally used in areas where highheat loss is a problem, such as conservatories.

ProWarm Electric Underfloor Heating  150w Sticky Mat Kit:
All of our heating mats can be laid either way up, they have a sticky mesh on one side and three strips of double sided tape on the other side.This means that the heating mat can be firmly held in place whether it is installed with the cables facing down or facing up making your installation easier.NOTE: You may still need to use small pieces of duct tape to hold the mat in certain places to prevent it from rising when using a levelling compound.

Before you begin Installing:
Please read through these instructions carefully and check that you have all the components required. ProWarm Electric Underfloor Heating 150w Sticky Mat  is designed for installation below most tile/stone floor coverings, it may also be installed below engineered/laminate wood floors, vinyl and low tog thin carpets but in these cases the heating mat/s must be first covered with an 8-10mm thick suitable latex based levelling compound.
Always check with the floor covering manufacturer for suitability of use with electric Underfloor heating systems, also check the suitability of any adhesives/latex compounds that are intended to be used with both the floor coverings and the heating system.

Do’s for Installation
-Do read through these instructions carefully before beginning work.
-Do use flexible adhesives and grouts.
-Do test the cable before tiling.
-Do be careful not to damage or dislodge the cable during tiling.
-Do ensure the cable is spaced no closer than 50mm between loops.
-Do try to protect the cable with cardboard or carpet during tiling.
-Do wait at least 7 days before turning on the system.
-Do read the separate installation and operating instructions for the thermostat.
-Do ensure the joint between the cold tails and heating cable is beneath the tiles.

Dont’s for Installation
-Don’t attempt to cut the heating cable at any point.
-Don’t allow the wires to cross or touch.
-Don’t allow excessive foot traffic over the wire before tiling.
-Don’t cut tiles over the heating cable.
-Don’t place tools or stacks of tiles on top of cable.
-Don’t place any product over the floor covering that has a higher tog value than 2.5.
-Don’t place any bean bags or fixed furniture over the floor covering.
-Don’t place cable closer than 100mm near any pipes.
-Don’t turn on the heating mat/cable while it is rolled up or still on the drum.
-Don’t tape over the end joint or the cold tail joint

IMPORTANT
Please ensure that the cold tail joint (the join between the heating cable and flexible supply lead)
is fully encapsulated in adhesive or levelling compound underneath the floor covering.
Please ensure that the end joint (the join at the end of the cable which is black) is also fully
encapsulated in tile adhesive or levelling compound underneath the floor covering.
Both the cold tail joint and end joint MUST NOT be covered with tape, this can cause the cable to
overheat and eventually fail!
DO NOT BEND THE COLD TAIL JOINT AT ANY POINT

ProWarm Electric Underfloor Heating 150w Sticky Mat  come with a full lifetime warranty
The warranty does not cover installations made by unauthorized persons or faults caused by incorrect design by others / misuse / damage caused by others / damage in transit / incorrect installation and any other subsequent damage that may occur. Replacement will be fully chargeable if the damage is because of any of the above reasons.

Installation Notes
- The system requires a mains voltage 230/240v and must be connected by a suitably qualified person.
All wiring must conform to lEE 17th Edition Part P regulations.
- The cold tail on the mat is coloured black and is a twin core and earth cable, or in some instances it may
have a silver earth braiding wrap around the twin cores. The heating element also contains a built in return
meaning that it only has to be connected to the thermostat from one end.
- For larger areas, if two or more mats are supplied, it will be necessary to use a connection or junction box to
join the heating mats (cold leads) together prior to connecting a single cable to the thermostat (Wire used
must be of a suitable size, selected by an electrician). MAX Load on one thermostat 16Amps.
- The electrical and electromagnetic fields generated are negligible and well within all recommended European
and International guidelines.
- The heating mats must not overlap and the heating cable MUST NOT be cut or cross at any point.
- The joint between the heating cable, cold tail and end joint MUST be located under the floor and
encapsulated in self levelling or tile adhesive and MUST NOT be taped over.

-Find all our Thermostats Here

-Find all our Heat Pumps Here
-Find all our Pipe Tools Here

-Find all our Trains And Drains Here

-Find all our Manifolds Here

ProWarm Electric Underfloor Heating 150W Sticky Mat ( 14m2 - 2 mats )